朝凯煤矿露天台阶爆破装药结构优化应用研究

本文以神达朝凯煤矿正在开采的台阶为工程背景,针对该矿在台阶爆破过程中存在着大块率高、根底多的现象,通过改变装药结构的方式对爆破参数进行优化。实践证明,优化后大块率和根底问题的治理效果明显。     

近50年大黑河流域气候水文要素变化趋势及突变分析

基于大黑河流域6个气象站1966～2013年气温、降水量、蒸发皿蒸发量、相对湿度和日照时数长期数据系列,采用气候倾向率和滑动t检验法分析了近50年大黑河流域气象要素的变化趋势及变异年份。结果表明,大黑河流域整体呈现暖干气候倾向,气温呈显著增高趋势,变化率为0.43～0.57℃/10a,气温增温变点大致出现了两次,分别在1986、1997年;降水量和蒸发量多呈不显著减少趋势,降水量先减(1981年)后增(1990年),蒸发皿蒸发量先减(1986年)后增(1996年);相对湿度、日照时数多呈显著减小趋势。     

移动物料信息分布式传输方法及应用

在流程工业生产中,移动物料计量信息的传输普遍采用电台和无线模块。接收电台周围环境严重影响计量信息的传输效果,尤其是钢结构厂房、电磁干扰区内,数据传输过程中的丢包率、误码率相当严重。本文提出一种多节点分布式传输方法,根据各个生产作业区环境条件设置相应的WIFI节点数,实现对作业区的无线信号覆盖。网络覆盖区内无线模块、PDA终端(PDA)、终端查询设备通过节点工作频段和阵列天线自适应调节,实现数据传输最佳化。铜熔炼生产现场测试表明,此种传输方法可以有效消除周围环境的电磁干扰,数据丢包率低于0.1%。     

Electrochemical hydrogen storage performance of as-cast and as-spun RE-Mg-Ni-Co-Al-based alloys applied to Ni/MH battery

The La-Mg-Ni-Co-Al-based AB₂-type La_0.8–xCe_0.2Y_xMgNi_3.4Co_0.4Al_0.1 (x=0, 0.05, 0.1, 0.15, 0.2) alloys were prepared via melt spinning. The analyses of the X-ray diffraction (XRD) and scanning electron microscopy (SEM) proved that the experimental alloys contain the main phase LaMgNi₄ and the second phase LaNi₅. Increasing Y content and spinning rate lead to grain refinement and obvious change of the phase abundance without changing phase composition. Y substitution for La and melt spinning make the life-span of the alloys improved remarkably, which is attributed to the improvement of anti-oxidation, anti-pulverization and anti-corrosion abilities. In addition, the discharge capacity visibly decreases with increasing the Y content, while it firstly increases and then decreases with increasing spinning rate. The electrochemical kinetics increases to the optimum performance and then reduces with increasing spinning rate. Moreover, all the alloys achieve to the highest discharge capacities just at the initial cycle without activation.     

Effect of thermomechanical processing on microstructure and mechanical properties of CoCrFeNiMn high entropy alloy

The CoCrFeNiMn high entropy alloy was produced by homogenization, cold rolling and recrystallization. The effects of thermomechanical processing on microstructures and tensile properties at different temperatures were investigated using X-ray diffractometry (XRD), optical microscopy (OM), scanning electron microscopy (SEM) and multi-functional testing machine. The results show that dendritic structures in cast alloy evolve into equiaxed grains after being recrystallized, with single face-centered cubic (FCC) phase detected. The most refined alloys, stemming from the highest rolling ratio (40%), exhibit the highest strength due to the grain boundary strengthening, while the variation of elongation with temperature shows a concave feature. For the coarse-grained alloys, both the ductility and work hardening ability decrease monotonically with increasing temperature. Serrated flow observed at intermediate temperatures is attributed to the effective pinning of dislocations, which manifests the occurrence of dynamic strain hardening and results in the deterioration in ductility. Besides, dimples on the fracture surfaces indicate the typical ductile rupture mode.     

Optimization of three-dimensional boiling enhancement structure at evaporation surface for high power light emitting diode

A theoretical model of phase change heat sink was established in terms of thermal resistance network. The influence of different parameters on the thermal resistance was analyzed and the crucial impact factors were determined. Subsequently, the forming methods including ploughing–extrusion and stamping method of boiling enhancement structure at evaporation surface were investigated, upon which three-dimensional microgroove structure was fabricated to improve the efficiency of evaporation. Moreover, the crucial parameters related to the fabrication of miniaturized phase change heat sink were optimized. The heat transfer performance of the heat sink was tested. Results show that the developed phase change heat sink has excellent heat transfer performance and is suitable for high power LED applications.     

极端耗水层带精准识别和调堵新技术

油田注水开发后期,部分油层存在极端耗水层带,存在耗水量大,注水驱油效率低,水循环成本高的开发问题,精准认识并有效封堵极端耗水层带,可提高注水利用率。目前国外出现了应用磁性纳米粒子的精细表征新技术及超顺磁性纳米颗粒封堵新技术,抑制极端耗水,实现低成本、高强度、深度堵调。     

高泉背斜地层压力测井多参数综合解释与异常高压成因

目前国内外地层压力测井解释方法较多,但大多数方法基于欠压实沉积理论并局限于单一的地层岩性,尤其是针对盆地边缘山前深层构造,单一测井参数确定地层压力误差较大,且无法解释沉积压实机制以外的异常高压。为此,将多种异常高压机制相关的测井参数进行综合解释,建立适合山前复杂构造的地层压力测井多参数计算模型,评价准噶尔盆地南缘高泉背斜高探1井的地层压力剖面,其计算结果与钻井实测数据吻合,相对误差小于3.00%.同时,基于原始沉积加载—卸载过程力学原理,利用地层压力测井多参数分析判别出高泉背斜深层各层系异常高压的形成机制。     

Enhanced piezoelectric strain of BiFeO3–Ba(Zr0.02Ti0.98)O3 lead-free ceramics near the phase boundary

The xBiFeO₃-(1-x)Ba(Zr_0.02Ti_0.98)O₃ + 1.0 mol% MnO₂ (xBF-BZT) lead-free piezoelectric ceramics were prepared by conventional solid-state reaction method. The structure, dielectric, and piezoelectric properties were studied. X-ray diffraction (XRD) analysis showed that xBF-BZT ceramics exhibited pure perovskite structure with the coexistence of tetragonal and rhombohedral phases (0.66 ≤ x ≤ 0.74). The Curie temperature T_c, the dielectric constant ε_r (1 kHz), dielectric loss tanδ (1 kHz), piezoelectric constant d₃₃, coercive field E_c (80 kV/cm), and remnant polarization P_r (80 kV/cm) of 0.7BF-0.3BZT-Mn ceramics were 491°C, 633, 0.044, 165 pC/N, 35.6 kV/cm, and 22.6 μC/cm², respectively. The unipolar strain of 0.7BF-0.3BZT reached up to 0.20% under the electric field of 60 kV/cm, which is larger than that (0.15%) of BiFeO₃–BaTiO₃ ceramics. These results indicated that the xBF-BZT ceramics were promising candidates for high-temperature piezoelectric materials.     

In Silico Study on Tumor-Size-Dependent Thermal Profiles inside an Anthropomorphic Female Breast Phantom Subjected to Multi-Dipole Antenna Array

Electromagnetic hyperthermia as a potent adjuvant for conventional cancer therapies can be considered valuable in modern oncology, as its task is to thermally destroy cancer cells exposed to high-frequency electromagnetic fields. Hyperthermia treatment planning based on computer in silico simulations has the potential to improve the localized heating of breast tissues through the use of the phased-array dipole applicators. Herein, we intended to improve our understanding of temperature estimation in an anatomically accurate female breast phantom embedded with a tumor, particularly when it is exposed to an eight-element dipole antenna matrix surrounding the breast tissues. The Maxwell equations coupled with the modified Pennes’ bioheat equation was solved in the modelled breast tissues using the finite-difference time-domain (FDTD) engine. The microwave (MW) applicators around the object were modelled with shortened half-wavelength dipole antennas operating at the same 1 GHz frequency, but with different input power and phases for the dipole sources. The total input power of an eight-dipole antenna matrix was set at 8 W so that the temperature in the breast tumor did not exceed 42 °C. Finding the optimal setting for each dipole antenna from the matrix was our primary objective. Such a procedure should form the basis of any successful hyperthermia treatment planning. We applied the algorithm of multi for multi-objective optimization for the power and phases for the dipole sources in terms of maximizing the specific absorption rate (SAR) parameter inside the breast tumor while minimizing this parameter in the healthy tissues. Electro-thermal simulations were performed for tumors of different radii to confirm the reliable operation of the given optimization procedure. In the next step, thermal profiles for tumors of various sizes were calculated for the optimal parameters of dipole sources. The computed results showed that larger tumors heated better than smaller tumors; however, the procedure worked well regardless of the tumor size. This verifies the effectiveness of the applied optimization method, regardless of the various stages of breast tumor development.